Page 3 of 5

Re: TERMINATOR T-800 1/2 scale

PostPosted: Thu Jul 11, 2019 8:09 pm
by casper
Now take the lower jaw form issue 6 and attach the head motor joint from issue 7, It just clips into place with four location pegs.

Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Thu Jul 11, 2019 8:14 pm
by casper
Now to take the "lower jaw" assembly from issue 5 and after adding the two brass bushes screw them together. The bushes allow a nice stiff joint for the lower jaw to move.

Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Thu Jul 11, 2019 8:17 pm
by casper
Issue 12
Assembling the right forearm

Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Fri Jul 12, 2019 3:28 pm
by casper
This was the most challenging assembly so far but still fairly easy.
Each muscle spring has to be superglued in place before the small cover is screwed to the forearm

Image
Image
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Fri Jul 12, 2019 7:08 pm
by Morris
Been watching this one come together

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:44 am
by casper
Issue 13
Assembling the neck and right finger
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:52 am
by casper
After fitting the lower neck joint to the left side of the neck its added to the left side of the jaw assembly using two 6mm screws

Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:52 am
by casper
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:55 am
by casper
Right side added using two 6mm screws. Looks really good apart from the join down the centre of the neck but If not showing on the front it would have been down the sides.
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:58 am
by casper
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Mon Jul 15, 2019 8:58 am
by casper
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Wed Jul 17, 2019 8:38 pm
by casper
dry fit :) looking good so far

Image
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:32 am
by casper
Now to add the push fit (Plastic) screw covers
I added a touch of superglue to the posts to secure them.
Image
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:38 am
by casper
Now I have my replacement issue 4 I can return to assembling the right upper arm
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:44 am
by casper
simple assembly for the upper arm pistons, one small screw holds a rubber washer/grommet on the end to give a nice seal when pushed together.
Image
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:50 am
by casper
shoulder joint assembly. Black part was superglued into position using the four location pegs
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:54 am
by casper
The two screws go in from the rear of the assembly so to hold them in place a little bit of blue tac was used till the front section was added and the whole thing was turned over and screwed down.
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 9:58 am
by casper
Image
Image
Image
Image
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 5:38 pm
by casper
Back on track :)
Issue 14
Fourth Finger and Lower arm tubes
Image

Re: TERMINATOR T-800 1/2 scale

PostPosted: Sun Jul 28, 2019 5:40 pm
by casper
Tubes are plastic :(
Image